contact  site map  
 

Triton - Technical Specifications

You can also download the specifications below as .pdf datasheet.

 

 

Specifications @ TA = 25 ΊC, fs = 48 kHz, fin = 1 kHz, fout = 1 kHz, 16 bit data, 0 dB input gain, unless otherwise noted.

Parameter

Condition

Min

Typ

Max

Unit
Input 1, 2          
Input voltage1) Full scale peak voltage
Nominal RMS level
Headroom at nominal RMS level
Allowable AC voltage
Allowable DC voltage		 1.95
-6.2
 
 
-10		 2.00
-6.0
12
 
  		2.05
-5.8
 
25
10		 V
dBV
dB
V
V
Overload voltage   1.38
-0.2		 1.41
0.0 		1.43
 		 Vrms
dB
Input impedance
(see figure 1)		   18.3 18.5 18.6 kW
Frequency range
(see figure 3)		 dB re 1 kHz level    dB re median level
     +0.04…-0.06                   ±0.05
     +0.05…-0.25                   ±0.15
     +0.05…-0.95                   ±0.5
     +0.05…-3.0                     ±1.5		  
60
20
9
4		    
22 k
23 k
23 k
23 k		 Hz
Resolution   8, 16 bit
Sample frequency   8  11.025  16  22.05
32   44.1   48		 kHz
Output 1, 2          
Output voltage1) Load impedance = 10 kW
Full scale peak voltage
Nominal RMS level
Headroom at nominal RMS level
Allowable DC voltage		  
1.95
-6.2
 
-2		  
2.00
-6.0
12
  		 
2.05
-5.8
 
2
V
dBV
dB
V
Load impedance

Nominal
2 outputs simultaneously, each output
1 output at a time

  
1
0.5		 10
 
 		   kW
Output impedance
(see figure 1)		   104 107 110 W
Frequency range
(see figure 4)		 dB re 1 kHz level    dB re median level
     +0.1…-0.1                      ±0.1
     +0.1…-0.5                      ±0.3
     +0.1…-0.9                      ±0.5
     +0.1…-2.9                      ±1.5		  
7
4
3
2		    
14 k
19 k
21 k
21 k		 Hz
Resolution   8, 16 bit
Sample frequency   32   44.1   48 kHz
Loopback2)          
SNR Full scale/Silence, unweighted 0...24 kHz   87   dB
Crosstalk Channel 1 to 2, vice versa, 0…24 kHz   -85    
THD+N Full scale, input + output 2)   -80    
USB          
Compatibility   USB 1.1  
Power consumption   1 unit
load
Connector   USB-B  
Cable length Cable supplied 1.8 m
General          
Supply current Output load impedance: 2 x 1 kΩ, full scale sine wave. Input overload LED’s on   70 85 mA
Audio connectors   RCA Phono  
Dimensions w x h x d 82 x 22 x 40 mm3
Weight     105   g

Alterations reserved 

 

 



Figure 1. Equivalent analog input and output circuits.

Notes

1.    A measurement report on the input and output full scale voltage levels at 1 kHz is provided with each individual Triton.

2.    Because system measurements are often performed by generating an excitation signal at the output, while recording the system response at the input, measurement system quality parameters depend on the Triton input + output chain. Therefore these parameters are given for the loopback configuration depicted in figure 2.



Figure 2. Loopback configuration.

 

Figure 3. Typical input frequency characteristic.
   
 
 

 Figure 4. Typical output frequency characteristic.